cfa11497c4103dadfa48985fce1f435790f6b234
howto/Quagga.md
| ... | ... | @@ -18,47 +18,49 @@ To connect to bgpd use: |
| 18 | 18 | $ vtysh |
| 19 | 19 | |
| 20 | 20 | Which provides an interactive interface. |
| 21 | -In this interface the following commands can be used: |
|
| 21 | +In this interface '?' can be used to list the available commands or subcommands. |
|
| 22 | 22 | |
| 23 | -The following text use this placeholders: |
|
| 23 | +## Configure Quagga |
|
| 24 | +a minimal config would look like this: |
|
| 24 | 25 | |
| 25 | -- `<AS>` your Autonomous System Number (only the digits) |
|
| 26 | -- `<GATEWAY_IP>` your gateway ip (the internal dn42 ip address you use on the host, where dn42 is running) |
|
| 27 | -- `<SUBNET>` your registered dn42 subnet, which you allocated on [nixnodes](https://io.nixnodes.net/) |
|
| 28 | -- `<PEER_IP>` dn42 ip of your peer who is connected with you using your favorite vpn/tunnel protocol (openvpn, ipsec, tinc, ...) |
|
| 29 | -- `<INTERFACE>` Interface which is used to connect to the peer, in case of openvpn it is the tun device |
|
| 30 | -- `<PEER_AS>` Autonomous System Number of your peer (only the digits) |
|
| 26 | + vtysh> configure terminal |
|
| 27 | + vtysh(config)> router bgp <your-asn> |
|
| 28 | + vtysh(config-router)> neighbor <neighbor-ip> remote-as <neighbor-asn> |
|
| 29 | + vtysh(config-router)> neighbor <neighbor-ip> interface <interface> |
|
| 30 | + vtysh(config-router)> exit |
|
| 31 | + vtysh(config)> exit |
|
| 31 | 32 | |
| 32 | -## Configure a new ipv6 peering |
|
| 33 | +### IPv6 |
|
| 34 | +for IPv6 do something like |
|
| 33 | 35 | |
| 34 | -In your interactive vtysh session type the following: |
|
| 36 | + vtysh> configure terminal |
|
| 37 | + vtysh(config)> router bgp <your-asn> |
|
| 38 | + vtysh(config-router)> neighbor <neighbor-ip> remote-as <neighbor-asn> |
|
| 39 | + vtysh(config-router)> neighbor <neighbor-ip> interface <interface> |
|
| 40 | + vtysh(config-router)> no neighbor <neighbor-ip> activate |
|
| 41 | + vtysh(config-router)> address-family ipv6 |
|
| 42 | + vtysh(config-router-af)> neighbor <neighbor-ip> activate |
|
| 43 | + vtysh(config-router-af)> exit |
|
| 44 | + vtysh(config-router)> exit |
|
| 45 | + vtysh(config)> exit |
|
| 46 | + |
|
| 47 | +### peer groups, prefix lists and such |
|
| 48 | +If you want to use 'prefix-list' to filter some of the prefixes quagga is receiving, you can use a 'peer-group' instead of apply the prefix list to every neighbor. |
|
| 35 | 49 | |
| 36 | -``` |
|
| 37 | -vtysh> configure terminal |
|
| 38 | -vtysh> router bgp <AS> |
|
| 39 | -vtysh> neighbor <PEER_IP> remote-as <PEER_AS> |
|
| 40 | -vtysh> neighbor <PEER_IP> peer-group dn |
|
| 41 | -vtysh> neighbor <PEER_IP> interface <INTERFACE> |
|
| 42 | -vtysh> no neighbor <PEER_IP> activate |
|
| 43 | -vtysh> exit |
|
| 44 | -vtysh> address-family ipv6 |
|
| 45 | -vtysh> neighbor <PEER_IP> activate |
|
| 46 | -vtysh> neighbor <PEER_IP> soft-reconfiguration inbound |
|
| 47 | -vtysh> exit |
|
| 48 | -``` |
|
| 50 | +Define a peer group: |
|
| 49 | 51 | |
| 50 | -## Configure a new ipv4 peering |
|
| 52 | + vtysh(config-router)> neighbor <peer-group-name> peer-group |
|
| 53 | + |
|
| 54 | +Apply to a neighbor: |
|
| 55 | + |
|
| 56 | + vtysh(config-router)> neighbor <neighbor-ip> peer-group <name> |
|
| 57 | + |
|
| 58 | +Apply a prefix list for incoming prefixes to your peer group: |
|
| 59 | + |
|
| 60 | + vtysh(config-router)> neighbor <peer-group-name> prefix-list <prefix-list-name> in |
|
| 51 | 61 | |
| 52 | -``` |
|
| 53 | -vtysh> configure terminal |
|
| 54 | -vtysh> router bgp <AS> |
|
| 55 | -vtysh> neighbor <PEER_IP> remote-as <PEER_AS> |
|
| 56 | -vtysh> neighbor <PEER_IP> peer-group dn |
|
| 57 | -vtysh> neighbor <PEER_IP> interface <INTERFACE> |
|
| 58 | -vtysh> exit |
|
| 59 | -``` |
|
| 60 | 62 | |
| 61 | -# show bpg session status |
|
| 63 | +## show bpg session status |
|
| 62 | 64 | |
| 63 | 65 | in this example: |
| 64 | 66 | * an active bgp session exists with peer 64713. |